![]() ![]() When a client on the same internal network as the web server requests a connection to the web server’s public IP address, the connection breaks. The client receives the reply packet it expects, and the connection is established. When I change last digit in ID from 0 to 1, I can register new gateway in V3. Set full policy=“local,telnet,ssh,ftp,reboot,read,write,policy,test,winbox,password,web,sniff,sensitive,api,romoĪdd address=44.150.168.221/24 interface=ether1 network=44.150.168.0 Set supplicant-identity=MikroTikĪdd address= down-port=1700 name=“TTS Cloud (eu1)” up-port=1700Īdd address=eu.work down-port=1700 name=ttn-v1 up-port=1700 Station-pseudobridge ssid=MikroTik station-roaming=enabled Set antenna-gain=0 country=no_country_set frequency-mode=manual-txpower mode= Here is my > export hide-sensitive may/31/2021 19:29:02 by RouterOS 6.48.3 software id = BS0G-I4NA model = RBwAPR-2nD serial number = C0220B14ED28 The V2 is OK, but has Status:unknown for the gateway and in V3 I got error: ID taken. Is there a working example for configuration on both sides? I was trying to register new gateway on V2 and V3 witgout success. I also added in the firewall of the mikrotik that udp and tcp is allowed on eth1.īut still no luck to get it connected to TTN. I added port forwarding for port 1700 udp and tcp on my ISP router in client mode. Set 0 forward=crc-valid name=OE1KFR_GW servers=TTN-EU-open Ipsec-policy=out,none out-interface-list=WAN “defconf: drop all from WAN not DSTNATed” connection-nat-state=!dstnatĬonnection-state=new in-interface-list=WANĪdd action=accept chain=input in-interface=ether1 protocol=udpĪdd action=accept chain=output out-interface=ether1 protocol=udpĪdd action=accept chain=input in-interface=ether1 protocol=tcpĪdd action=accept chain=output out-interface=ether1 protocol=tcpĪdd action=masquerade chain=srcnat comment=“defconf: masquerade” “defconf: accept established,related, untracked” connection-state=Īdd action=drop chain=forward comment=“defconf: drop invalid” “defconf: accept to local loopback (for CAPsMAN)” dst-address=127.0.0.1Īdd action=drop chain=input comment=“defconf: drop all not coming from LAN”Īdd action=accept chain=forward comment=“defconf: accept in ipsec policy”Īdd action=accept chain=forward comment=“defconf: accept out ipsec policy”Īdd action=fasttrack-connection chain=forward comment=“defconf: fasttrack” “defconf: accept established,related,untracked” connection-state=Īdd action=drop chain=input comment=“defconf: drop invalid” connection-state=Īdd action=accept chain=input comment=“defconf: accept ICMP” protocol=icmp ![]() Supplicant-identity=MikroTik wpa-pre-shared-key=Īdd name=dhcp ranges=192.168.88.10-192.168.88.254Īdd address-pool=dhcp disabled=no interface=wlan1 name=defconfĪdd address=us. down-port=1700 name=TTN-USĪdd address=eu. down-port=1700 name=TTN-EUĪdd address=.work down-port=1700 name=TTN-EU-openĪdd comment=defconf interface=wlan1 list=LANĪdd comment=defconf interface=ether1 list=WANĪdd address=192.168.88.1/24 comment=defconf interface=wlan1 network=Īdd address=10.0.0.140/24 interface=ether1 network=10.0.0.0Īdd address=192.168.88.0/24 comment=defconf gateway=192.168.88.1 Set authentication-types=wpa2-psk mode=dynamic-keys Outdoor mode=ap-bridge ssid=MikroTik-B8825D station-roaming=enabled Set band=2ghz-b/g/n channel-width=20/40mhz-XXĬountry=austria disabled=no distance=indoors frequency=auto installation= ![]() Similar posts did not point me in the correct direction. ![]() Sorry to ask for help or double post, but my knowledge on router configuration is not that good and I have still not managed to get it connected to TTN EU network. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |